How to correctly use commercial ultrasonic cleaning machine
Tinggalkan pesanan
Here is to talk about the operating rules of ultrasonic cleaning machine.
1. Ultrasonic cleaning machine installation
General ultrasonic cleaning machine power line and ultrasonic cleaning machine is separate, first of all to the ultrasonic power supply and cleaning tank butt. An ultrasonic cleaner with a drain can be connected to the drain pipe, or the drain can be directed towards the drain.
2. Add water to ultrasonic cleaning machine
Add proper amount of water in the cleaning tank, the liquid level should be able to soak the cleaning parts, and lower than the highest water line. Some models with overflow, should be connected in advance overflow pipe.
3. Ultrasonic cleaning machine heating
Set the temperature to start the heating switch, adjust the water temperature to the appropriate temperature (generally between 50 degree -60 degree ). There is a temperature detector in the cleaning machine, the heating device will continue to heat to the specified temperature, and then in the heat preservation mode, when the temperature is lower than a certain value, the heating device will automatically start and heat to the set temperature.
4. Ultrasonic cleaning machine to add cleaning agent
When the water temperature rises to about 30 degree , parts cleaning agent can be added to the cleaning tank, can be added in accordance with the product process, the proportion is 1:20 or 1:30, you can stir the water to make the cleaning agent fully dissolved into the water.
5. Preprocessing of parts
In the use of ultrasonic cleaning machine to clean some oil is too thick parts, before cleaning can be scraped thick mud, or thick powder dust, simple ultrasonic cleaning pretreatment will greatly improve the efficiency of ultrasonic cleaning, shorten the ultrasonic cleaning time, prolong the service life of ultrasonic cleaning machine.
6. Place parts of ultrasonic cleaning machine
Place the parts in the stainless steel cleaning basket and gently put them into the cleaning tank. It is recommended not to put too many parts in one time, and try to evenly distribute them and do not place them too compact.
7. Start the ultrasonic cleaning machine
Set the cleaning room, open the ultrasonic cleaning function, start the normal cleaning work.
8. Ultrasonic cleaning machine stopped
Ultrasonic cleaning working time can be determined according to the parts, in the ultrasonic cleaning process if you feel that the cleaning is almost finished, directly turn off the ultrasonic switch.
9. Ultrasonic cleaning machine post-processing
Take out the cleaning basket directly and rinse the cleaned parts with clean water. Then place the parts in the fan or air drying machine for air drying, until the gap hole is completely blown dry. Some manufacturers directly use double groove, a groove ultrasonic cleaning, a groove rinse or spray cleaning, save the trouble to move.
10. Ultrasonic cleaning machine cleaning agent processing
When the ultrasonic cleaning machine is used to clean a lot of parts, the content of sludge in the cleaning liquid is very high, coupled with the emulsification of ultrasonic, the cleaning liquid will be muddy, so that not only the secondary pollution of parts, but also the cavitation of ultrasonic will therefore be weakened, then the liquid containing cleaning agent should not continue to use.
Some plants have environmentally friendly water treatment systems that can be refined and discharged; Some units according to the output of cleaning, in the purchase of ultrasonic acoustic wave cleaning machine at the same time, increased the filter circulation device, cleaning while filtering impurities, improve the production efficiency; In some cases, the cleaning liquid of the day is put into the water storage tank, and the next day after precipitation, the new cleaning liquid is added to use. It should be said that the three methods are helpful to reduce the use cost.
11. Auxiliary effect of soaking before ultrasonic cleaning
In the cleaning of many parts, such as cylinder head, piston, connecting rod, turbocharged turbine, intake and exhaust pipe, etc., with carbon or oxide layer, floating on the surface of the light is easy to clean, and the heavy is more difficult to wash, then the necessary soaking softening process of parts, will make the next stage of cleaning twice the result with half the effort.
12. Auxiliary functions of ultrasonic cleaning machine
Cleaning the accumulation of small sheet, granular, complex shape parts, can use a variety of functions combined with the method, such as side cleaning, side throwing, side cleaning side basket rolling, pulse cleaning every few minutes, pause soaking and cleaning.






